Peltier-cooled Incubator IPP410eco

The Memmert single display, compressor cooled IPP410eco Incubator is recommended for large volumes in conjunction with rapid temperature changes. Peltier technology provides seamless heating and cooling within a single system, reducing operating costs.

Let us help you build the perfect Incubator. Contact us for customization options and pricing.

SKU: IPP410eco Categories: , Tag:


Cooled Incubator IPP410eco


Working temperature range in °C from 0 (at least 20 below ambient temperature) to +70°C
Temperature 1 Pt100 sensor DIN class A in 4-wire-circuit

Control technology

Language setting German, English, Spanish, French, Polish, Czech, Hungarian
ControlCOCKPIT SingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition TFT-color display
Timer Digital backwards counter with target time setting, adjustable from 1 minute to 99 days
Function SetpointWAIT the process time does not start until the set temperature is reached
Calibration three freely selectable temperature values
adjustable parameters temperature (Celsius or Fahrenheit), air flap position, program time, time zones, summertime/wintertime


Convection forced ventilation by Peltier fan
Fresh air admixture adjustment of pre-heated fresh air admixture by air flap control in 10 % steps
Vent vent connection with restrictor flap


Documentation programme stored in case of power failure
Programming AtmoCONTROL software for reading out, managing and organising the data logger via Ethernet interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software available as accessory (on demand).


Temperature control adjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class 1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperature
Autodiagnostic system for fault analysis

Standard equipment

Internals 2 stainless steel grid(s), electropolished
Works calibration certificate for +10°C and +37°C
Door fully insulated stainless steel doors with 2-point locking (compression door lock)

Stainless steel interior

Interior easy-to-clean interior,made of stainless steel, reinforced by deep drawn ribbing with integrated and protected large-area heating on four sides
Volume 384 l / 13.6 cu. Ft.
Dimensions 25.2 x 47.2 x 19.7 inches (d less 1.3” for fan – Peltier)
Max. number of internals 8
Max. loading of chamber 440 lbs
Max. loading per internal 44 lbs

Textured stainless steel casing

Installation on lockable castors
Dimensions w(D) x h(E) x d(F): 32.4 x 67.7 x 25.8 inches (d +2.2” door handle)
Housing rear zinc-plated steel

Electrical data

Voltage Electrical load 230 V (± 10%), 50/60 Hz approx. 2.6 amps @ 230 V

115 V (± 10%), 50/60 Hz approx. 5.2 amps @ 115 V

Ambient conditions

Set Up The distance between the wall and the rear of the appliance must be at least 15 cm. The clearance from the ceiling must not be less than 20 cm and the side clearance from walls or nearby appliances must not be less than 5 cm.
Altitude of installation max. 2,000 m above sea level
Ambient temperature +5 °C to +40 °C
Humidity rh max. 80 %, non-condensing
Overvoltage category II
Pollution degree 2

Cooled Incubator IPP410 Packing/shipping data

Transport information The appliances must be transported upright
Customs tariff number 8419 8998
Country of origin Federal Republic of Germany
WEEE-Reg.-No. DE 66812464
Dimensions approx incl. carton w x h x d: 1330 x 1440 x 1050 mm
Net weight approx. 161 kg
Gross weight carton approx. 227 kg

Additional information

Weight 319 lbs
Dimensions 27 × 30 × 46 in